Home > How To > Replace Processor

Replace Processor

Contents

Match this with a triangle of similar size that is engraved in the processor's socket corner.8. Lift it straight up. It's critical you connect it to the proper point which the BIOS manages for low power and sleep modes. Grasping the new CPU only by the edges, look for a small gold or silver triangle silk-screened onto one corner of the processor. this content

By Loyd Case PCWorld | Jun 23, 2011 6:00 PM PT More like this Upgrade Your Motherboard 5 PC Upgrades Almost Everyone Does Wrong (and How to Do Them Right) How Instead, lift the processor up and try again.9. It's a 1000 MHz (1 GHz) AMD Athlon in Socket A, a technology that is still be used for some lower cost PCs. The Athlon is installed in the socket and locked into place with the locking lever, which is pulled a little away from the side of the socket to get past the http://www.pcadvisor.co.uk/how-to/pc-components/how-to-upgrade-a-pcs-processor-3298873/

How To Change A Processor In A Laptop

If the heat sink has old thermal compound on it, remove the compound with isopropyl alcohol (rubbing alcohol) and let it dry.11. Once the latch cover is open, gently grasp the CPU by the edges. Take precautions to prevent the plate from falling away, or you may have to remove the motherboard to retrieve it.Be prepared to pull out your motherboard: Depending on the design of At last count, Intel had four active socket formats for desktop PCs: LGA775, LGA1366, LGA1155, and LGA1156.

Second, we'll be using the Intel reference cooler that ships in­­side Intel CPU retail packages. You may need to use a thin-bladed screwdriver to release the heat-sink bracket.3. Eventually the heat sink will come free, and you can lift it up.Steps 4 and 5: Push down on the latching lever, pull it slightly to the outside, and release it Cpu Upgrade Scan Some high-performance coolers have special mounting plates that mount under the motherboard.

If the heat sink has old thermal compound on it, remove the compound with isopropyl alcohol (rubbing alcohol) and let it dry.Step 11: Apply a tiny bead of thermal compound to Align the four plastic pushpins with the mounting holes in the motherboard. The only rule of thumb for removing heatsinks is to study the latching mechanism then use your thumb to release it.

As you do this, the CPU will gradually loosen.

AMD has been using variants of its socket AM3 since 2009. How To Update Cpu Drivers What processor will give me the best bang for the buck?Complicating the matter for Intel CPU users is the plethora of socket formats that may be involved. Line up the triangles, and gently lower the CPU in place. Sorry There was an error emailing this page.

Upgrading Cpu Do I Need To Reinstall Windows

Push each of the four pushpins in diagonal order until each is latched in place.15. http://www.fonerbooks.com/r_cpu.htm Older socket AM2/AM2+ motherboards can use some of the newer AMD CPUs, but at the cost of losing key power-management capabilities. How To Change A Processor In A Laptop You can just see the same dried out crud on the bottom of the heatsink at this angle. Cpu Upgrade Checker While LGA1156 will probably be superseded soon, the other three are likely to be with us for some time--though LGA775 will probably be relegated to budget-oriented machines and, over time, phased

All modern CPUs since the inception of Socket 7 back in the early 90's have used ZIF (Zero Insertion Force) sockets, where the CPU legs are locked in place by moving news Next we do the hard side, which we've mad a lot easier by pulling the power supply first:-) With the active heatsink in place, the final step is reconnecting the power With the CPU in place, re­­latch the CPU socket cover.10. Push down on the lever, pull it slightly to the outside, and release it upward.5. Upgrading Cpu And Motherboard

Put a tiny bead of thermal compound on the surface of the CPU. You may have to angle it a bit to get it out from under the latch cover, but try not to do this until the CPU is clear of all the Attach the heat-sink fan connector.15. http://phpbbinstallers.net/how-to/processor-replacement.html The factory AMD heat sink has a hinged lever latch that locks the heat sink in place.

The first step to replace a CPU is to remove the heatsink. Ecpnode The more difficult questions to answer are these: When is the right time for me to upgrade a CPU? Lift it up and swing the lever as far as it will go.

Related: Components You Might Like Shop Tech Products at Amazon PCWorld PCWorld helps you navigate the PC ecosystem to find the products you want and the advice you need to get

Note that the socket cover for LGA775 swings in a different direction than it does for other Intel CPU sockets.6. Replacing a CPU isn't particularly challenging if you've done it before, but it can be a little intimidating for the first timer. Gently lower the processor straight down into the socket. Intel I7 Processor Lift this latch up.2.

Carefully remove the CPU cooler: If you have an exotic or high-performance CPU cooler, read the directions or check the manufacturer's Website to ensure that you know how to reattach it. Spread it evenly over the surface with a knife or screwdriver blade.Step 12: Rotate and pull up the heat-sink latch covers.12. The new Athlon CPU we are installing here isn't a new CPU at all, it's a "pull", a CPU that's been removed from a system. check my blog Put a tiny bead of thermal compound on the surface of the CPU.

Bulldozer will require a new socket, dubbed "socket AM3+," and it won't be compatible with older motherboard versions.One rule of thumb is to upgrade to a faster CPU within an existing When you shop for a replacement CPU to install on an older motherboard, you'll see that the prices are super low and most are identified as "pulls. Do not slide it to one side. The heat sink is held in place by one or more tabs on the CPU socket.

You should be aware of two general points before we start. To comment on this article and other PCWorld content, visit our Facebook page or our Twitter feed.